5 Basic things to do with your new Garmin GPS after you take it out of the box
Congratulations, you’ve just bought your first Garmin GPS. But what now?
Well here are the first 5 things that we recommend you do as soon as you take your New Garmin GPS out of the box, to ensure that your unit runs smoothly and without hassles.
1. Charge the battery:
With the GPS Street Navigators like the Nuvi and Zumo units, you can either charge the unit using an AC charger (if you have one) or, use a standard USB PC cable to plug the unit into your PC and charge it that way. The charge from the PC is quite a bit slower than that from an AC charger but it works just as well. The unit will go into “mass storage mode” as soon as you plug it into your PC (i.e. a picture of a PC will appear on the screen and you will not be able to do anything on the unit while it is in this mode). The unit will also upload all the necessary drivers to your PC at this time.
For the outdoor handheld GPS units you will have to insert your own AA (penlight) sized batteries. If you are going to be using alkaline batteries, we would recommend using a decent brand (like Duracell) rather than just the cheapest you can find.
2. Get a First Fix:
If your New Garmin GPS unit came with preloaded maps on a memory card, pop the card into the unit, take it outside and switch it on. Make sure that you have a good (unobstructed) view of the sky and don’t move around too much. Allow the unit about 30 minutes to get a decent first satellite fix. This will give it time to download a full set of GPS almanac data which will speed up all subsequent satellite signal searches. After this, it shouldn’t take more than a minute or two at most to get a satellite signal again (usually only around 30 seconds or so).
Note:
When you first switch a Garmin Nuvi or Zumo unit on, it will ask you to complete a few basic Setup steps. These steps are different on each unit but can include:
- Setting your location (country) – some of the older units do not have South Africa on the country list. If this is the case then simply select the United Kingdom (UK) and then further set your timezone to be +2 hours.
- Daylight saving preference (for SA it is always “Off“).
- Language.
- And sometimes even the “Units” (km or miles)
.
3. Register your unit and your map software on your new GPS:
For South African Garmin users, you only need to register (your ownership of the unit and the map software) on the Garmap.co.za website and not on the Garmin website. Halfway down the Garmap main page you will see something like this:
For “Plug-and-Play” users (i.e. owners of the Nuvi and Zumo series units) - click on the first link. Outdoor handheld unit owners (eTrex mapping series, GPSMAP 60 series, GPSMAP 76 series, Colorado and Oregon units) - click on the 3rd “CD Users” link to register your products.
International Garmin users (i.e. those with City Navigator USA, Europe, Australia etc maps) would need to register their units and maps on the International myGarmin.com website.
4. Update your Garmin GPS Firmware:
You never know how long your new GPS unit has been sitting on the shop shelf and it is highly probable that there has already been a firmware (the operating system or “Software” for our American and European readers) update released for your unit in the meantime. Go to the Garmin.com website and download a small (4.31MB) program called WebUpdater for your PC or Mac.
Once you have the WebUpdater program loaded onto your computer, simply connect your GPS unit to your computer and run the program. WebUpdater will automatically detect which unit you have connected and then download the relevant firmware updates for you. See this post for more info on firmware updates as well as step-by-step instructions.
Important Note: Please remove any preloaded “Plug-and-Play” memory cards from your unit before updating your firmware. We have had a few reports of people who have had their detailed maps on the memory cards corrupted during this process.
5. Update or Load the latest Speedtrap data:
As in the previous step, your preloaded speedtrap database may also be a bit out of date by the time you open the box of your new Garmin GPS. This step is only applicable to those of you with Nuvi and Zumo units (and of course this is also only for the South African speedtrap database – Garmin users in other countries will have to do a Google search for their local databases and instructions). This step can be a bit confusing for those of you who are not regular computer users so you may want to ask if your local GPS dealer can do it for you before you take delivery.
Firstly you will need to go back to the Garmap.co.za website. Just to the right of the previous “Register your unit” links you will see a grey column and at the bottom this column will be the following links:
The first link is to the international Garmin.com website where you will need to download and install another small program called POI Loader onto your computer.
The second link is to a PDF document with full of instructions on how to download the Garmap Speedtrap database from the Garmap website, unzip the database files, organize the various files and folders and then upload the database to your unit using the POI Loader program. Please read through the document before you continue (I know. I know, it’s boring but it is necessary ;-).
You will then have to log in to the Garmap website (using the email address and password that you used to register your unit and maps in Step 3) before you can download the database. Once you are logged in, click on the third link and on the next page look for the following text (Note: the text only becomes links once you have logged in):
Before logging in
And after logging in
Then simply follow the instructions in the PDF instructions document to update or load your speedtrap database on your Nuvi / Zumo unit.
I shall be posting a slightly more advanced “Set Up” tips list for your New Garmin GPS unit in another day or two as well as a few more posts on Search Tips, Creating & Uploading Routes and other Tips & Tricks (including hidden menu screens on the Nuvi units), so please come back and visit us soon. If there is anything that you think should be included, please leave a comment below.
Please rate this post: 
(4 votes, average: 4.50 out of 5)
Loading ...
Related Posts
If you've enjoyed reading this post then please subscribe to our RSS Feed.
Loading ...
great info. could you perhaps include a list of garmin conventions eg screen symbols and what parameters are used in eta calc? what speed is taken as default to give eta before moving off?
I have a new nuvi 850-I miss the speed monitoring which I had on my old Garmin when driving to a programmed destination. Are there any updates to get it, and if so, what must I do and how do I do it?
Guys…for some reason when I am trying to update my Nuvi 200 firmware..(got it yesterday) with the webupdater it goes well until the download reaches 89% and then it stops…and the seconds for time remaining go back up and it never goes past 89%! anybody have any idea whats going on?? Please give me some assistance here.